Free model: fitted drawer organiser bin

No licence key and no account are needed for these.

• Cutlery drawer organiser for a shallow kitchen drawer: a 245 by 160 mm tray module with two long channels.
• Tool drawer organiser: a 200 by 150 mm bin with 2 mm walls and four compartments.
• Desk drawer organiser: a low 180 by 120 mm tray with six compartments.
• Kitchen drawer organiser for small utensils: a 210 by 105 mm bin, 55 mm high, with three pockets.
• Makeup drawer organiser: a 160 by 120 mm tray with eight small pockets.
• Choosing clearance for a snug fit: measure your printer with a 40 by 30 mm test bin.

Pipe clips with screw tabs

These use the pipe and cable clip model, which needs a licence key.

• 15 mm pipe clip: one tab, for small-bore copper and plastic tube.
• 16 mm pipe clip: one tab, for conduit and multilayer pipe.
• 20 mm pipe clip: one tab, for conduit and irrigation pipe.
• 22 mm pipe clip: two tabs, sized for copper tube.
• 25 mm pipe clip: one tab, for pipe, rails and tool handles.
• 28 mm pipe clip: two tabs, for copper tube and round rail.
• 32 mm pipe clip: two tabs, with a note on nominal waste pipe sizes.
• 40 mm pipe clip: two tabs, for waste pipe and dust hose.
• 50 mm pipe clip: two tabs and a wide opening, for large pipe and hose cuffs.

Cable clips

These also use the pipe and cable clip model, which needs a licence key.

• 4 mm cable clip: for thin charging and speaker cables.
• 6 mm cable clip: for a network or USB cable, 3 mm screw.
• 8 mm cable clip: for mains flex, HDMI and coax.
• 10 mm cable clip: for a thick power lead or a small bundle.
• 12 mm cable clip: for a heavy extension lead or a bundle of three or four cables.

Bit holders and screwdriver racks

The hex bit holder strip and the screwdriver rack need a licence key.

• 1/4 inch hex bit holder for 10 bits: one row, 99 mm long.
• 1/4 inch hex bit holder for 12 bits: a compact block, two rows of six.
• 1/4 inch hex bit holder for 20 bits: two rows of ten.
• 1/4 inch hex bit holder for 30 bits: three rows of ten for a full set.
• 4 mm precision bit holder: twelve pockets for electronics driver bits.
• Screwdriver rack for 6 screwdrivers: wall mounted, 168 mm long.
• Screwdriver rack for 8 screwdrivers: 208 mm long, prints on a 220 mm bed.
• Screwdriver rack for 12 slim screwdrivers: 244 mm long, 20 mm spacing.

Bins compatible with Gridfinity grid dimensions

The bin on a 42 mm base grid needs a licence key. It has plain square feet and no stacking lip, and this generator is independent of the Gridfinity project.

• 1x1 bin: 41.5 mm square, 28 mm high.
• 2x1 bin: 83.5 by 41.5 mm, two compartments.
• 2x2 bin: 83.5 mm square, 63 mm high, four compartments.
• 3x1 bin: 125.5 by 41.5 mm, one long tray.
• 3x2 bin: 125.5 by 83.5 mm, six compartments.
• 4x2 bin: 167.5 by 83.5 mm, four lanes.

Drill guide jigs with an edge fence

The drill guide jig needs a licence key.

• 3 mm drill guide: pilot holes 10 mm from an edge.
• 4 mm drill guide: handle screw and pilot holes 15 mm from the edge.
• 5 mm drill guide: shelf pin holes 37 mm from the edge.
• 6 mm drill guide: dowel holes 20 mm from the edge.
• 8 mm drill guide: thick block, or sized for a metal bushing.
• 10 mm drill guide: 18 mm block for dowel and bolt holes 30 mm from the edge.